how-to-install-a-bathroom

How To Replace Bathroom Fan

DIY Shower Room Follower Setup: Maintain the Wetness Out by Placing a Restroom Fan In

You may be stunned to discover that installing or changing a shower room exhaust follower is a reasonably very easy Do It Yourself project. All you require are the right devices as well as fundamental electric and carpentry abilities. Comply with the actions listed below for brand-new installation or replacing an existing exhaust follower.

Prepare to Mount Your Shower Room Fan
Before you can mount your brand-new restroom fan, you need to follow these steps:

1. Compute your shower room’s CFM score.

You can make certain you buy the appropriate toughness fan by calculating the CFM (cubic feet per min) of your shower room. Increase the space’s cubic footage (length x width x height) as well as divide by 7.5.

2. Exactly how silent (or loud) do you desire your brand-new restroom fan to be?

In the majority of spaces, a loud fan is aggravating, yet in the bathroom it’s desirable. Audio rankings on more recent washroom followers vary between 0.5 (really quiet) as well as 6 (really loud). Choose the ranking that will finest fit your needs.

3. Where do you want to set up the brand-new bathroom fan?

The placement of the follower can influence airflow. The best area to mount your follower is at the center factor between your shower as well as a toilet.

If you are setting up a new bathroom exhaust follower: Make certain to extend the area out above in your attic. This is where the bulk of the follower will certainly be located. It must be between 2 joists in an unobstructed area.
If you are changing a restroom exhaust follower: It’s most convenient to place the brand-new one in the same area.
Before you begin your DIY restroom follower installation, make certain you have all the devices and materials you require.

how to replace bathroom fan

Replacing an Existing Restroom Exhaust Fan

If you just require to change an existing washroom exhaust fan, you’ll locate it a little much easier because you do not require to cut openings in the ceiling or roofing system. Right here’s just how to replace a bathroom follower.

1. Turn the electric power to the shower room OFF at the breaker.

This will certainly keep you from getting an unpleasant shock.

2. Obtain under the grille to disconnect as well as separate.

There is possibly a lot of particles in there, so put on gloves, safety and security goggles as well as a respirator. Eliminate the grille covering from the old follower.
Unscrew or disconnect the electric motor blower setting up from the housing device, then open the electric splice device as well as very carefully take out the cords.
Eliminate the adapters and also untwist the cords to separate them. (Ensure electrical power is off first.).
Loosen the wire clamp to release the electric cable television from the fan housing.

3. Separate the housing system in the attic.

In the attic, separate the air duct pipeline from both the air vent cap port duct as well as the housing system.
Pull the electric wire and also wiring without the housing system.
Utilizing your power drill, remove the screws holding the old follower’s brackets to the joists. Lift the old fan through the ceiling.

4. Install your brand-new follower.

If your new follower coincides with dimension as your old one, you can install it right now. If it’s larger, you’ll need to reduce a bigger opening with a drywall saw. If it’s smaller size, you can caulk around the sides of the real estate system to fill in the spaces once the fan is installed.

Most likely to the attic room and reduced the brand-new fan into the hole.
Slide-out the extendable placing brackets and protect them to the joists using your power drill as well as 1-inch (2.5 cm) drywall screws. You might desire a person to hold the follower in place from listed below.

5. Link the duct.

When the follower is in place, affix a 90-degree duct arm joint to the fan’s exhaust port using sheet metal screws. After that affix a new 4- to 6-inch (10.2 to 15.2 cm) air duct pipeline to the air duct elbow joint.

6. Attach as well as protect the circuitry.

Insert the electrical cord with the brand-new fan’s port and also secure it with a cable television clamp.
Open up the electric splice box (from either the attic or the bathroom, depending upon the model) and pull out the follower cables.
Connect the electrical cords to the follower cables by turning very same color cords together and connecting a cable adapter.
Cover the bare copper wire under the ground clip or screw and also tighten to protect.
Put all of the wires back into the electric splice box and also replace the cover.

7. Plugin and also re-attach the grille.

Go back to the bathroom and also mount the motor blower assembly by connecting it right into the receptacle and screwing it to protect it. Affix the grille. Evaluate your brand-new follower by transforming the power back on.

Congratulations– now you have a new restroom follower! Your brand-new fan will keep your washroom tidy and dry, shielding it from mold as well as mildew. Secure the remainder of your residence with a residence warranty from American House Guard ®. Contrast our plans on the internet today as well as select the protection that functions finest for you.

Scroll to Top